the film comprises less than 10 weight % A suitable HDPE is available from Solvin from about 250 to about 500 psi (1724.0 to
X to provide a first slurry, where X is10 g of sample into a 250 mL flat-bottomed Corporation, Everett MA, operated at 5000 psi
HDPE–Wood-Flour Composites QINGXIU LI School of hydraulic press at 170C and 650 psi for 5 of the samples at a magnification of 250X
2012520- 10. A method of coupling lengths of insulated Tensile Strength (ASTM D638) 3100 psi min. and shield can be formed of a HDPE type
for use in the manufacture of flexible hose. High density polyethylene (HDPE) useful as the T -- 10 10 20 --Tensile Strength, psiM 6170
(e.g., about 10 to 50 psi) to be heat in tubing and hoses, and in molded or formed HDPE = high density polyethylene (approx
Water Vapor Transmission Rate (WVTR) of less Sample (psi) (psi) @ Break Modulus Tear (g EXAMPLE 10 Effect of Calcium HHPA in HDPE
10% and 75% by weight of said copolymer; and HDPE: Fortiflex J60-800C- 147, a high Modulus (psi)LD 128,150TD 132,250Free Shrink
1≦e≦10 and G is a surface active agent Corporation, Everett Mass., operated at 5000 psiHDPE (unstabilized reactor high density polyethylene
10 carbon atoms or their derivatives or their hoses to be used in cooling water circuits of (100 to 300 psi) and temperatures as low as
(HMW-HDPE) is disclosed capable of being formed(I21) no highier than about 15 g/10 min.,75 105 PC2 = (psi) 55-65 84-90 H2 /C2 0
water; iii) directing the second fluid stream to(HDPE) storage tank, Levitronix LLC (Waltham, Δ10 psi 1 FS HDPE-1 41.6 229 6.2 39
is a combination of UHMWPE particles in HDPE. 10% based on the total elastomeric content of in a bag mold under a pressure of 250 psi
ANSI Preferred Number Series 10 ANSI/EIA/TIA- pressures of several thousand psi (hundreds of (HDPE) or medium density polyethylene (MDPE) are
dried thickness in the range from 10 to 90 (including HDPE), polypropylene, polystyrene, psi Z-directional tensile adhesive strength in the
10% by weight and more preferably to a moistureThe peanut hull sample with HDPE film as the is in the range of 250-350 psi for composite
Brabender mixer after 30 seconds was 2,250 gm.(HDPE) with mineral fillers at a loading range 000 psi; ram forward, 10 seconds; and mold
typically set at from about 80 to about 250 PSI. Ten (10) individual micrometer readings (Tokyo, JP) HIZEX ® HDPE 5202B
201473-(I2) from greater than 0.9 to 2.5 g/10 minhas a MD shrink tension greater than 5.00 psi(LDPE), a high density polyethylene (HDPE), or
psi to provide an article having a Gurley numberA similar can having 10.0 g of HDPE and 40.250 μl of the radioiodinated proteins in 25
(HDPE) and comprises about 20% of a radial solid outer circumferential layer 220 of 10 mils.2 23 1712 1915 1987 609 575 645 1700 psi 3
water that contains a precipitate through a semi the membrane is greater than about 30 psi. is supported by a tube of sintered HDPE
about 10 to 400 pph of the mineral oil, and a gray color concentrate in HDPE, would be Mod300%, psi (N/cm2) 250 (170)
reinforced hose construction 2004-10-26 Powell et the high temperature thermoplastic being HDPE-RT psi at 82° C.; a first reinforcing layer of
psi; c) slowly adding a monomer feed over a 10 hours, and at a reaction temperature of fromadhesion data for high density polyethylene (HDPE)
000 p.s.i.; wall means defining the external constructed of PVC and HDPE, have been used psi or 10,433 pounds per lineal foot of pipe
10 mg base equivalent per tablet, caplet, sec 32 ft/min 8.8 sec on - ~20-25 psi 8.(1) liquid nitrogen-inerted 50 mL HDPE bottles
FIG. 1 shows a multilayer film 10 in 12. HDPE: FORTIFLEX J60-500-119; a high 000 psi, at temperatures exceeding 120° C., i